Home
Company Info
Contact Us
Sales Terms
Privacy Policy
Kitty Cat
Brakes/Throttle
Chassis Parts
Clutch Parts
Drive Train
Engine Parts
Fuel System
Hardware
Hoods &
Seats
Skis/Steering
Technical Services
& Engine Work
Track/Suspension
Traction/Control
Tools
Service Manuals
Polaris 120
Engine Parts
Traction/Control
Clutches & Parts
Arctic Cat
120
Ski & Spindle Assy
A-arm Assy
Front Suspension
Steering & Tie Rod
Drive Train & Brake
Slides, Idlers, Track
Rear Suspension
Chassis & Bumper
Hood & Windshield
Belly Pan & Exhaust
Gas Tank & Seat
Engine Parts
Air Cleaner
Carburetor
Cylinder & Case
Piston & Crank
Recoil Starter
Throttle Control
Magneto
*Traction/Control
*Clutches
& Parts
*Parts
Diagrams
Classified Ads
Information and submit
Trailers
Kitty Cats
Polaris 120
Arctic
Cat 120
Ski Doo 120
Clothing
Wanted
Favorite Links:
>Kids
Pro Ice West
NW MN & E. ND
>KCPRO-East
Northeast MN
>WI
Kitty Cat Racers
Wisconsin
>WI
Kids Snowmobile
Racing Association
Northern WI
>Michigan
SnoX
All MI
>Rock
Maple Racing
Northeast USA
Other Links:
>KittyCatSnowmobiles
Message Board
| |
FS-500 DIGITAL TACHOMETER
FEATURES:
SenDEC's FS500 is a surface mountable Tachometer/Hour meter that features a
resetable job timer in addition to a totalizing hour meter. The tachometer is
accurate to 16,000 rpms and features a resetable maximum RPM recall. This
multifunction meter is programable to three different firing patterns to
accommodate two and four-stroke engines.
SPECIFICATIONS:
-
Operating temperature: -40C to 70C -
LCD digit height: 0.200 -
Dimensions: 2.8" W x 1.78" D x 0.69" H -
Weight: 0.130 lbs -
Tachometer Resolution:
P1... 40 RPM
P2... 20 RPM
P3... 80 RPM -
Display update time: 1.5 seconds
OPERATION:
Push and release mode control to toggle between Hour Meter, Tachometer, Job
Timer, and Service Alarm (SVC TIME, SVC SET).
Hour Meter - Indicated by "TOT TIME" on display (non-resettable accumulated
running hours.)
Tachometer - Upon entering this function, you will see "P1", "P2", or "P3" for 3
seconds on the right-hand side of the display. This is the current programmed
firing pattern. To access MAXTACH (highest engine RPM), be in the RPM mode and
hold the mode button down for at least three seconds. To erase the high RPM,
continue holding down for at least 9 seconds (will see 0000). To change the
firing pattern, be in the RPM mode and hold the mode button down for more than
10 seconds, then release the button on the desired firing pattern ("P1", "P2",
or"P3").
Job Timer - To view the JOB TIME, push and release the mode button until the
display reads "JOB TIME". To reset to zero, depress the mode button for three
seconds (time will clear to 0.0)
Service Time - This is the time built up since your last maintenance. To view
the Service Time, push and release the mode button until the display reads "SVC
TIME". When this time exceeds what you set in SVC SET, the display will start
flashing (alarming you to perform maintenance). After the maintenance is
performed, hold down the mode button for 3 seconds. This will clear the SVC TIME
to 0.0 and the alarm will stop flashing. You are now ready to go toward your
next maintenance interval.
Service Set - This is where you set the desired maintenance interval. To view
the set maintenance interval, push and release the mode button until the display
reads "SVC SET". To set a different service interval, push and hold the mode
button until the desired interval appears on the display. Then simply release
the mode button and that is your new service interval. (The mode button must be
held down for at least 3 seconds before the Service Set intervals begin to
increment.
ENVIRONMENTAL SPECIFICATIONS:
-
Operating temperature: -40F to 160F (-40C to 71C) -
Shock: SAE J1378 55g -
Vibration: SAE J1378 20g -
Humidity: SAE J1378 95% RH -
100% Epoxy encapsulated -
Case Material: ABS, black or white -
Weight 1 oz -
Warranty: Two years for OEMs -
Waterproof to 70' below surface -
UL & CUL recognized, CE approved
|